 |
» |
|
|
|
|
|
|
|
|
HP Photosmart 5510 e-All-in-One Printer Series - Setting up the All-in-One (Hardware)
Introduction
This document explains how to set up the physical parts of the product. Complete these steps before
you install the product software on your computer. If you already set up the product hardware, and need software installation help, see Links to Software Installation Instructions
at the end of this document. This document includes the following steps to set up the product:
Check the contents of the box
Unpack the product
Connect the power cord and turn on the power
Select the language and location
Insert the cartridges
Load paper
Align the cartridges
Looking for the driver?
If you did not already set up the hardware, follow the steps in this document to do so first. But, if you already installed the hardware and are just looking for the driver to download, click this link
HP Software and Driver Downloads
. For instructions on how to install the software, here are some shortcuts: Setting up the All-in-One
Follow these steps in order. When you are finished, you can click the appropriate link at the end of this document if you need instructions to install the product software.
| CAUTION:
|
Do NOT connect the USB cable now. If you need a USB cable to connect the product to the computer, you will be prompted to connect it at the correct time during software installation. |
Step one: Check the contents of the box
The contents might vary by country/region. See the packaging for a list of items shipped in the box.
Step two: Unpack the All-in-One
Remove all tape and packing material
from the product.
Figure 1: Remove all packing material
Image: Remove all packing material Open the cartridge access door, and then remove the tape from inside the product.
Figure 2: Open the cartridge access door, and then remove the tape from inside the product
Image: Open the cartridge access door, and then remove the tape from inside the product Close the cartridge access door.
Figure 3: Close the cartridge access door
Image: Close the cartridge access door Pull out the paper tray, and then remove the tape from the tray.
Figure 4: Remove tape from the paper tray
Image: Remove tape from the paper tray Push the paper tray back into the product.
Step three: Connect the power cord and turn on the All-in-One
Connect the power cord to the rear of the product, and then plug it into a wall outlet.
Figure 5: Connect the power cord
Image: Connect the power cord Press the Power button ( 
) to turn on the product. Figure 6: Press the Power button
Image: Press the Power button
Step four: Select your language and country/region
When you first turn on the product, it prompts you to select your language and region. Follow these steps to set the default language and country/region for your product.
Touch your desired language, and then touch Yes
to confirm the language choice. The Set Region Menu displays.
Touch your desired region, and then touch Yes
to confirm the country/region choice.
Step five: Load photo paper
|
NOTE:
|
If you do not have photo paper or if you prefer to load photo paper in the future, skip to the next step in this document. |
Open the paper tray door, pull out the paper tray, and then slide the paper width guides to their outermost positions.
Figure 7: Pull out the paper tray and slide the paper width guides to their outermost positions
Image: Open the paper tray door and then slide the paper width guides to their outermost positions Load a stack of photo paper into the tray, with the short edge facing toward the product and the print side down. Push the stack into the tray until it stops.
Figure 8: Load photo paper into the tray
Image: Load photo paper into the tray Slide the paper width guides in until they rest against the edges of the paper.
Figure 9: Slide the paper width guides until they rest against the edges of the paper
Image: Slide the paper width guides toward the photo paper Close the paper tray, and then open the paper tray extender.
Step six: Load plain paper
If the paper tray door is closed, open the paper tray door, and then pull out the paper tray.
Slide the paper width guides to their outermost positions.
Figure 10: Slide the paper width guides to their outermost positions
Image: Slide the paper width guides to their outermost positions Load a stack of plain paper into the tray with the short edge facing toward the product and the print side down (if the paper has a print side). Push the stack into the tray until it stops.
Figure 11: Load paper into the tray
Image: Load paper into the tray Slide the paper width guides until they rest against the edges of the paper.
Figure 12: Slide the paper width guides against the edges of the paper
Image: Slide the paper width guides against the edges of the paper Close the paper tray, and then pull open and lift the paper tray extender until it is fully extended.
Step seven: Install the cartridges
Open the cartridge access door. The carriage moves to the access area.
Figure 13: Open the cartridge access door
Image: Open the cartridge access door Remove the protective cap from the carriage.
Figure 14: Remove the protective cap from the carriage
Image: Remove the protective cap from the carriage Pull the orange tab to remove the plastic wrap from a cartridge.
Figure 15: Remove the plastic wrap from a new cartridge
Image: Remove the plastic wrap from a new cartridge Remove the orange cap from the cartridge. Twist the cap counter-clockwise until it snaps off.
Figure 16: Remove the orange cap from the cartridge
Image: Remove the orange cap from the cartridge With the nozzle and the contacts facing down, push the cartridge into its slot. Press down on the cartridge until it clicks into place.
Make sure that the color icon on the cartridge label matches the color icon on the slot.
Figure 17: Insert the cartridge
Image: Insert the cartridge Repeat these steps to insert the other cartridges.
Close the cartridge access door.
Figure 18: Close the cartridge access door
Image: Close the cartridge access door
Step eight: Align the cartridges
|
NOTE:
|
After you load the cartridges and close the cartridge access door, the product automatically prompts you to print an alignment page. |
On the product control panel, touch OK
. The product prints an alignment page.
Open the lid.
Figure 19: Open the lid
Image: Open the lid Place the alignment page on the scanner glass with the printed side down, and then position it on the front right corner of the glass.
Figure 20: Place the alignment page on the scanner glass
Image: Place the alignment page on the scanner glass Close the lid, and then touch OK
. The alignment page scans.
If the product does not
automatically print an alignment page, follow these steps:
From the home screen, touch the Right Arrow ( 
), and then touch the Setup icon ( 
). Touch Tools
.
Touch the Down Arrow ( 
), and then touch Align Printer
. The product prints an alignment page. Open the lid.
Figure 21: Open the lid
Image: Open the lid Place the alignment page on the scanner glass with the printed side down, and then position it along the front right corner of the glass.
Figure 22: Place the alignment page on the scanner glass
Image: Place the alignment page on the scanner glass Close the lid, and then touch OK
. The alignment page scans.
Links to software installation instructions
After you complete the previous setup steps, you can install the product software with the product CD or by downloading the software from the HP Web site. For instructions, click the link for your connection type and your computer operating system.
Important
: Do NOT connect the USB cable yet. You will be prompted to connect it at the correct time during software installation. Getting started with ePrint
Now you can stay connected and productive on the go with ePrint. ePrint lets you print directly to your ePrint-enabled HP printer using a smartphone, notebook, or other mobile device. For additional information related to setting up and using ePrint, click the link provided.
|
|
Printable version
