 |
» |
|
|
|
|
|
|
|
|
HP LaserJet Pro P1566 and P1606dn Printers - Setting Up the LaserJet (Hardware)
Introduction
This document explains how to set up the physical parts of the product. Complete these steps before
you install the product software on your computer. If you already set up the product hardware, and need software installation help, see Links to Software Installation Instructions
at the end of this document. This document includes the following steps to set up the product:
Follow these steps in order. When you are finished, you can click the appropriate link at the end of this document if you need instructions to install the product software.
| CAUTION:
|
Do NOT connect a USB cable now. If you plan to use a USB cable to connect the product to the computer, you will be prompted to connect it at the correct time during software installation. |
Step one: Check the contents of the box
Remove the product from the box, and then check the contents of the box.
The contents might vary by country/region. See the packaging for a list of items shipped in the box.
Step two: Remove packing tape
Remove all packing tape from the product.
Step three: Prepare the print cartridge
Open
the print cartridge door.
Figure 1: Open the print cartridge door
Illustration: Open the print cartridge door. Lift up the paper packing, but do not remove it.
Figure 2: Lift the paper packing
Illustration: Lift the paper packing. Remove the print cartridge packaging.
Figure 3: Remove the print cartridge packaging
Illustration: Remove the print cartridge packaging. Remove the print cartridge from
the product.
Figure 4: Remove the print cartridge
Illustration: Remove the print cartridge. | CAUTION:
|
To prevent damage to the print cartridge, hold the print
cartridge at each end. |
Remove the packaging from inside the product.
Figure 5: Remove the packaging from inside the product
Illustration: Remove the packaging from inside the product. Remove the orange clip from the end of the print cartridge.
Figure 6: Remove the orange clip from the print cartridge
Illustration: Remove the orange clip from the print cartridge. Gently rock the print cartridge back and forth to distribute the toner evenly.
Figure 7: Rock the print cartridge
Illustration: Rock the print cartridge. Bend the tab on the left side of the print cartridge until the tab breaks loose. Pull the tab to remove all the sealing tape from the print cartridge.
Figure 8: Remove the sealing tape
Illustration: Remove the sealing tape. | CAUTION:
|
If toner gets on your clothing, wipe it off with a dry cloth and wash the clothing in cold water. Hot water sets toner into the fabric
. |
Insert the print cartridge, and then close the print cartridge door.
Figure 9: Insert the print cartridge and close the door
Illustration: Insert the print cartridge and close the door.
Step four: Prepare the trays
Insert the output tray.
Figure 10: Insert the output tray
Illustration: Insert the output tray. Insert the priority input tray.
Figure 11: Insert the priority input tray
Illustration: Insert the priority input tray
Step five: Load plain paper
Raise the priority input tray, and then slide the paper length and width guides to their outermost positions.
Figure 12: Slide out paper guides
Illustration: Slide out paper guides. Load plain paper in the main input tray with the top forward and the print side up.
Figure 13: Load paper
Illustration: Load paper into the main input tray. Slide the paper guides inward so that they rest against the stack of paper.
|
NOTE:
|
To prevent jams and skewing, always adjust the side and front paper guides. |
Figure 14: Adjust the paper guides
Illustration: Adjust the paper guides Lower the priority tray.
Figure 15: Lower the priority tray
Illustration: Lower the priority tray.
Step six: Connect the power cord
Connect the power cord to the back of the product.
Figure 16: Connect the power cord
Illustration: Connect the power cord to back of product Plug the power cord into an electrical outlet.
Step seven: Turn on power
Press the Power button ( 
) to turn on the product. Figure 17: Turn on the power
Illustration: Turn on the power. |
NOTE:
|
A blank page might print when you turn on the product for the first time. |
Links to Software Installation Instructions
After you complete the previous setup steps, you can install the product software. For instructions, click the link for your computer operating system and type of connection.
| CAUTION:
|
Do NOT connect a USB cable now. You will be prompted to connect it at the correct time during software installation. |
|
|
Printable version
