 |
» |
|
|
|
|
|
|
|
|
HP Designjet 1050c Printer - Product Specifications
Model number
| Description
|
Model number
|
|---|
| HP Designjet 1050c Printer
|
C6074A
|
Localization of introduction
Canada
USA
Middle East
Latin America
Europe
Asia Pacific
Africa
Serial number location
The serial number is located on the back cover.
Product description
The 1050c is a high-performance, high-speed, 36-inch, large-format printer using thermal Inkjet technology. Its new ink system (printhead + printhead cleaner + ink cartridges) provides 600 dpis and 350/175 cc of ink in a continuous refill system.
HP Jetdirect card
The 1050c has the HP Jetdirect 600n 10/100 TX (J3113A) installed.
Product features
Three times faster print speed (over the HP Designjet 750c+ printer)
Three times "click-to-clunk" overall throughput improvement (over the HP Designjet 750c+ printer)
True 600-dpi output for crisper text, finer lines, and improved image resolution
Addressable 1200-dpi mono resolution
Network-ready
1 GB hard disk option
Increased ink unattendedness with 350 cc/175 cc (CMY) and 350 cc (K) off-axis ink cartridges
Long-life print heads
Increased paper unattendedness with 300 ft HP Bright White paper Jumbo Rolls
Improved ink-level sensing (low-ink and overnight printing indicator)
Ability to load cut-sheet without manually unloading roll paper
Support for thin paper (Asian tracing paper)
Glossy paper support
HP-GL, HP-GL/2, and HP RTL languages supported
VarWare Support
Five times faster (than the HP Designjet 750c+) Adobe (R) PostScript (R) option
New Front panel for improved ease of use
EIO slots (one for hard disk, the other for networking)
EDO slots for RAM DIMMS (16, 32, 64 MB)
Parallel connector; 1 serial connector
Windows 3x, 9x, and Windows NT drivers shipped in the box
AutoCAD drivers shipped in the box
System requirements
Windows 9x
Windows 3x
Windows NT
UNIX (R)
|
NOTE:
|
If you have any questions about whether an application supports this printer, first check the software documentation, and, if necessary, contact the software vendor for advice. |
Connectivity
Industry-standard HP-GL, HP-GL/2 and HP-RTL languages supported
Adobe (R) Postscript(R) Level III option available
Built-in networking option through EIO (10/100-Base-T)
Two EIO slots (one for hard disk, the other for networking/fast direct connect)
Two EDO slots for RAM DIMMs up to 128 MB
One parallel connector
AutoCAD (Windows 3x, 9x, and Windows NT drivers shipped in the box)
Recommended cables
The following cables are recommended for optimum performance and electromagnetic compatibility.
Cables for PCs
| Interface type (computer)
|
HP part number
|
Cable length
|
Connector type at computer end
|
|---|
IEEE compatible/ Centronics Interface
(All)
|
C2951A
|
3.0 m (9.8 feet)
|
25-pin male
|
Cables for UNIX (R) systems
| Interface type (Computer)
|
HP part number
|
Cable length
|
Connector type at computer end
|
|---|
Parallel (IEEE compatible/ Centronics) Interface
(All)
|
C2951A
|
3.0 m (9.8 feet)
|
25-pin male
|
Fonts
PostScript option fonts
The fonts print shows all resident PostScript fonts (internal and downloaded) with a printed sample of each font.
Media specifications
Roll paper
| Characteristic
|
Specification
|
|---|
Paper length:
All film types
Heavyweight coated paper
|
91.4 m (300 feet)
38 m (125 feet)
30.5 m (100 feet)
|
| Maximum outside diameter of roll
|
99 mm (3.9 inches) across any diameter
|
| Inside core diameter
|
50.8 mm (2 inches)
|
| Roll widths
|
610 mm (24 inches) and
914 mm (36 inches)
|
| Side margins (normal)
|
5 mm (0.20 inches)
|
| Side margins (extended)
|
15 mm (0.59 inches)
|
| Leading edge
|
12 mm (0.47 inches)
|
| Trailing edge
|
5 mm (0.20 inches)
|
Sheet paper
The 1050c accommodates all standard and odd paper sizes. The width ranges from 210 mm to 917 mm (8.3 to 36.1 inches). The maximum sheet length is 1600 mm (63 inches).
Margins roll/sheet
| Specification
|
Side margins
|
Leading Edge margin
|
Trailing edge margin
|
|---|
Roll
(normal)
|
5 mm
(0.20 inches)
|
12 mm
(0.47 inches)
|
5 mm
(0.20 inches)
|
Sheet
(normal)
|
5 mm
(0.20 inches)
|
12 mm
(0.47 inches)
|
15 mm
(0.59 inches)
|
Roll
(extended)
|
15 mm
(0.59 inches)
|
12 mm
(0.47 inches)
|
5 mm
(0.20 inches)
|
Sheet
(extended)
|
15 mm
(0.59 inches)
|
12 mm
(0.47 inches)
|
15 mm
(0.59 inches)
|
Ink
The ink system in the 1050c printer includes three components: a print head, a printhead cleaner, and ink cartridge to provide large-capacity ink, unattended printing, ease-of-use, reliability, and low cost. The ink system offers true 600 dpi and new advanced dithering algorithms for exceptional image quality prints.
Each 600-dpi thermal Inkjet printhead applies ink droplets onto the paper and has a reservoir that holds enough ink for several prints. The printer automatically refills the print head from the ink cartridge whenever the ink volume in the printhead reservoir becomes low.
The printer uses the printhead cleaners to clean and maintain the print heads to ensure best possible image quality, and to seal the print heads when they are not in use to ensure long life.
HP80 ink supplies
The ink system components (the print head, the printhead cleaner, and the ink cartridge) are called the HP80 ink supplies, and they are coded with an HP80 icon to help with ordering the correct replacement components.
Each color ink cartridge (cyan, magenta, yellow, and black) can be purchased separately from HP retailers and should be purchased when an existing ink cartridge is low to print continuously.
A printhead and a printhead cleaner are supplied as a single unit and should always be installed as a matched pair. They do not require replacement every time a new ink cartridge is installed in the printer. It is only necessary to replace a print head and printhead cleaner when the existing components are time expired.
Part numbers for HP80 ink supplies are listed in the table below.
| Description
|
Part number
|
|---|
| Black print head and printhead cleaner
|
C4820A
|
| Cyan print head and printhead cleaner
|
C4821A
|
| Magenta printhead and printhead cleaner
|
C4822A
|
| Yellow printhead and printhead cleaner
|
C4823A
|
| Ink cartridge black 350 cc
|
C4871A
|
| Ink cartridge cyan 350 cc
|
C4846A
|
| Ink cartridge magenta 350 cc
|
C4847A
|
| Ink cartridge yellow 350 cc
|
C4848A
|
| Ink cartridge cyan 175 cc
|
C4872A
|
| Ink cartridge magenta 175 cc
|
C4874A
|
| Ink cartridge yellow/175 cc
|
C4873A
|
Memory
HP Designjet 1050c printers come with 32 MB of memory. You can expand the memory up to a maximum of 128 MB by adding additional 16 MB, 32 MB, or 64 MB memory expansion modules in various combinations.
Performance/print quality
| Print quality
|
Print resolution
|
|---|
| Fast
|
300 x 300 dpi
|
| Normal
|
600 x 600 dpi
|
| Best
|
Color prints:
600 x 600 dpi
Grayscale prints:
1200 x 600 dpi
|
Print speed
| Quality
|
Size
|
Mono speed
|
Color speed
|
|---|
| Normal
|
2 x 3 ft
(609 x 914 mm)
|
1:20
|
2:00
|
| Best
|
2 x 3 ft
(609 x 914 mm)
|
2:15
|
4:00
|
Accuracy
0.38 mm (0.015 inches) or 0.2% of the specified vector length, whichever is greater, at 23 degrees C (73 degrees F), 50 to 60% relative humidity on HP special polyester film.
Programming languages supported
CALS
HP-GL
HP-GL/2 (with Kanji Level 1 and 2 character sets)
HP-RTL (with color extensions)
PJL, PML
Adobe PostScript Level 3 (supports Asian languages)
VarWare
Reliability
| Feature
|
Description
|
|---|
| Reliability
|
35% Annualized Failure Rate (AFR)
|
| Duty cycle
|
14.77 sq. meters (159 square feet) per day
|
Physical specifications
| Feature
|
Description
|
|---|
| Weight
|
Without stand:
59 kg (130 pounds)
With stand:
81 kg (178 pounds)
|
| Length
|
1566 mm (61.7 inches)
|
| Depth
|
675 mm (26.6 inches)
|
| Height
|
1290 mm (50.8 inches)
|
Electrical specifications
| Feature
|
Description
|
|---|
| Source
|
100 to 240 volts AC +/- 10% autoranging
|
| Frequency
|
50 to 60 Hz
|
| Current
|
Three amp maximum
|
| Consumption
|
200 watts maximum
|
| Energy Star Rating (USA)
|
Maximum power in ideal state: 45 watts
|
Environmental specifications
|
NOTE:
|
If the printer temperature falls below the minimum specified operating temperature the printer may stop to protect the ink systems. At 3000 meters altitude, the printer may have operational problems. |
| Condition
|
Description
|
|
|---|
| Operating Range
|
Printing:
|
15 to 35 degrees C (59 to 95 degrees F)
at 20 to 80% relative humidity
|
| Optimal print quality:
|
22 to 26 degrees C (72 to 79 degrees F)
at 30 to 60% relative humidity
|
| Acceptable print quality:
|
15 to 30 degrees C (59 to 86 degrees F)
at 20-80% relative humidity
|
| Storage
|
Printer:
|
-40 to 70 degrees C (-40 to 158 degrees F)
|
| Packed system:
|
-40 to 60 degrees C (-40 to 140 degrees F)
|
Acoustic specifications
| Feature
|
Specification
|
|---|
| Operating sound pressure
|
54 dB (from a one-meter bystander position)
|
| Idle sound pressure
|
<30 dB (A) (from a one-meter bystander position)
|
| Operating sound power
|
6.5 Bels (A)
|
| Idle sound power
|
<4.3 Bels (A)
|
General warranty statement
| HP product
|
Duration of warranty
|
|---|
| Printer and related HP hardware
|
One year
|
| Printheads
|
700cc of ink consumption or until end of exp date (whichever is first)
|
| Ink cartridges
|
Until original ink is consumed or until end of expiration date (whichever is first)
|
| Software
|
90 days
|
Safety certifications
| Country/Region
|
Electromagnetic Compatibility (EMC) specifications
|
|---|
| Canada
|
Canadian Department of Communications, Radio Interference Regulations Class B (1) compliant
|
| European Union
|
89/336/EEC EMC Directive compliant
Meets EN 55022 Class B (1) emission limits, prEN 55024-2 ESD, prEN55024-3 Radiated Immunity, prEN 55024-4 Fast Transients.
|
| Japan
|
Registered VCCI Class B (1)
|
| Korea
|
RRL certified
|
| South Africa
|
SABS licensed
|
| USA
|
Federal Communications Commission
Class B (1) computing device
CFR 47 Part 15
|
Australia
New Zealand
|
Meets AS/NZS 3548
|
| Taiwan
|
BCIQ certified
|
(1) Product exhibits Class A operation when connected to LAN cables using Print Server accessories.
| Country/Region
|
Printer Safety Specification
|
|---|
| |
Information Technology Equipment (ITE),
Movable,
Class I,
Pluggable Type A,
Installation Category II,
Pollution Degree 2.
For indoor, controlled office environments use.
|
| Canada
|
Canadian Standards Association "Certified" ITE, CSA C22.2 No.950
|
| European Union
|
73/23/EEC Low Voltage Directive compliant. Meets EN 60950
|
| Mexico
|
DGN, NOM019-SCFI-1994 certified
|
| Norway
|
NEMKO approved,
EN 60950, EMKO TSE (74)DK207/94
|
| USA
|
Underwriters’ Laboratories
"Listed" ITE, UL 1950
|
| China
|
CCIB certified GB 4943-90 1st Ed.
|
| Czech Republic
|
EZU, IEC950 certified
|
| Singapore
|
PSB, SS337 certified
|
| Poland
|
PCBC certified
|
| Russia
|
GOST certified
|
Regulatory notices
To obtain a Material Safety Data Sheet (MSDS)
You can obtain current Material Safety Data Sheets for the ink systems used in the printer via the HP web site (www.hp.com)
Electromagnetic compatibility (EMC)
The US Federal Communications Commission (in 47 cfr 15.105) has specified that the following notice be brought to the attention of those using this product.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
| CAUTION:
|
Pursuant to Part 15.21 of the FCC Rules, any changes or modifications to this equipment not expressly approved by the Hewlett-Packard Company, may cause harmful interference and void the FCC authorization to operate this equipment.
|
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interferences by one or more of the following measures:
Reorient the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
You may find useful the following booklet prepared by the FCC: "How to Identify and Resolve Radio-TV Interference Problems". This booklet is available from the US Government Printing Office, Washington, DC 20402, and Stock No. 004-000-00345-4.
Shielded cables
Use of shielded data cables is required to comply with the Class B limits of Part 15 of the FCC Rules.
When connected to LAN cables using print server accessories
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.
DOC statement (Canada)
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
When connected to LAN cables using print server accessories, this digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
Telecommunications statement
The HP Designjet 1050c and 1055cm printers, models C6074 and C6075, are approved under Approval Number NS/G/1234/5/100003 for indirect connection to public telecommunication systems within the United Kingdom.
|
|
Printable version
