 |
» |
|
|
|
|
|
|
|
|
HP LaserJet 2200 - Product Specifications
| Printer specifications
|
HP LaserJet 2200
|
HP LaserJet 2200
w/ optional tray 3 (250-sheet)
|
HP LaserJet 2200
w/ optional tray 3 (500-sheet)
|
|---|
| Height: |
255 mm (10 inches)
|
334 mm (13.2 inches)
|
395 mm (15.6 inches)
|
| Width: |
405 mm (16.0 inches)
|
405 mm (16.0 inches)
|
405 mm (16.0 inches)
|
| Depth (body): |
435 mm (17.1 inches)
|
435 mm (17.1 inches)
|
435 mm (17.1 inches)
|
| Weight (with toner cartridge):
|
14.0 kilograms (29.0 pounds)
|
17.1 kilograms (35.9 pounds)
|
18.7 kilograms (39.4 pounds)
|
Electrical specifications
| Electrical specifications
|
110-Volt Models
|
220-Volt Models
|
|---|
| Power requirements: |
100-127V (+/- 10%)
50/60 Hz (+/- 3 Hz)
|
220-240V (+/- 10%)
50/60 Hz (+/- 3 Hz)
|
| Minimum recommended circuit capacity for typical product: |
5.0 Amps
|
2.5 Amps
|
| Average power consumption (watts) - HP LaserJet 2200 series printers: |
Printing (18 PPM) = 381 W
Standby = 12 W
PowerSave = 12 W
Off = 0 W
|
Printing (18 PPM) = 393 W
Standby = 14 W
PowerSave = 14 W
Off = 0 W
|
|
NOTE:
|
PowerSave default activation time is 15 minutes. Values are subject to change. |
| CAUTION:
|
Power requirements are based on the region where the printer is sold. Do not convert operating voltages. This may damage the printer and void the product warranty.
|
Environmental specifications
| Environmental specifications
|
Operating printing
|
Storage/standby
|
|---|
| Temperature (printer and toner cartridge): |
15 to 32.5 degrees C (59 to 89 degrees F)
|
-20 to 40 degrees C (-4 to 104 degrees F)
|
| Relative humidity: |
10% to 80%
|
10% to 90%
|
Acoustic emissions
| Bystander position
|
Declared per ISO 9296
|
|---|
| Printing (19 ppm/ltr, 18 ppm/A4): |
L pAm = 52 dB(A)
|
| PowerSave: |
Essentially inaudible
|
| Sound Power
|
Declared Per ISO 9296
|
| Printing (19 ppm/ltr, 18 ppm/A4)
|
L WAd = 6.6 bels(A)
|
| PowerSave
|
Essentially inaudible |
|
NOTE:
|
If placing printers with sound power equal to or greater than 6.3 bels in a separate room or cubicle, values are subject to change. |
Technical specifications
| Speed and throughput: |
19 ppm (letter) or 18 ppm (A4) rated engine speed (simplex), 5.5 ppm rated engine speed (duplex), instant-on fuser provides first page out in less than 15 seconds from warm or cold start (simplex) and less than 26 seconds using duplex, 133 MHz RISC microprocessor
|
| Print quality: |
HP Prores 1200 (true 1200 x 1200 dpi at up to 18 ppm), HP Fastres 1200** (1200 dpi like quality at up to 18 ppm), 600 dpi, adjustable line screen setting (141/180 lpi) to optimize print quality, ** Default setting
|
| Typefaces: |
HP PCL 6: 45 scalable True Type fonts built-in, HP Postscript(R) Level 2 emulation: 35 scalable True Type fonts built-in, HP Fontsmart software provides simple font management for Microsoft(R) Windows, Euro Symbol in-built (€)
|
| Memory: |
HP LaserJet 2200D/DT/DN/DSE printers: 8 MB RAM, 2 expansion slots, memory expansion up to 72 MB using 100-Pin SDRAM DIMMs. HP LaserJet 2200DTN printer: 16 MB RAM, 1 expansion slot, memory expansion up to 48 MB using 100-Pin SDRAM DIMMS. HP LaserJet 2200 series printers: optimized by Memory Enhancement technology (MEt)
|
| Printer languages: |
HP PCL 6, HP PCL 5e, HP Postscript Level 2 emulation
|
| Connectivity: |
HP LaserJet 2200 series printers: 1 bi-directional parallel port (IEEE 1284 ECP-compliant, B-size), 1 USB port (2.0 compliant), 1 wireless Fast InfraRed (FIR) port (IrDA compliant). HP Jetsend and OBEX enabled via FIR port. HP LaserJet 2200D/DT/DSE printers: 1 open Enhanced Input Output (EIO) slot for optional HP Jetdirect 600N/610N (EIO) internal print servers. HP LaserJet 2200DN/DTN printers: 1 HP Jetdirect 610N (EIO) internal print server for Ethernet 10/100Base-TX network environments (RJ-45 port)
|
| Paper handling: |
NOTE
: The simplex version of the HP LaserJet 2200 printer family (base model number C7064A) supports manual duplexing only.
HP LaserJet 2200 series printers: In-built automatic duplex unit, tray 1 is a 100-sheet/10 envelope multipurpose input tray for automatic and manual feeding of special media, tray 2 is a 250-sheet input tray, paper input level indicators, straight-through paper path, standard output capacity of 150-sheets (face-down). HP LaserJet 2200D/DN/DSE printer: optional 250-sheet input tray, optional 500-sheet input tray. HP LaserJet 2200DT printer: tray 3 is a 250-sheet input tray. HP LaserJet 2200DTN printer: tray 3 is a 500-sheet input tray.
Two output bins: select either the top output bin or the rear output bin for the most convenient output location. The Face-Down Output Bin, located on the top of the printer, has a 150-sheet capacity of 20-pound paper. The Face-Up Output Bin, a fold out bin located at the back of the printer, has a 150-sheet capacity of 20-pound paper.
|
| Media types and weights: |
Paper, envelopes, transparencies, card stock, postcards, labels and recycled paper - tray 1 handles 60 to 163 g/m 2(16 lbs. to 43 lbs), tray 2, tray 3 (HP LaserJet 2200DT/DTN), optional 250 / 500-sheet input trays and automatic duplex unit handle 60 to 105 g/m 2 (16 lbs to 28 lbs.). Envelopes: Typical capacity of 10 in tray 1, weight: 60 to 90 g/m 2 (16 lbs to 24 lbs.). Transparencies: Typical capacity of 75 in tray 1, thickness: 0.10 to 0.14 mm (.004 to .006 inches). Labels: Typical capacity of 50 in tray 1, thickness: 0.10 to 0.14 mm (.004 to .006 inches). Tray 1: Minimum size: 76 x 127 mm (3 x 5 inches), maximum size: 216 x 356 mm (8.5 x 14 inches), tray 2, tray 3 (HP LaserJet 2200DT) and optional 250-sheet input tray: A4: 210 x 297 mm (8.3 x 11.7 inches), A5: 148 x 210 mm (5.8 x 8.3 inches), Letter: 216 x 279 mm (8.5 x 11 inches), Legal: 216 x 356 mm (8.5 x 14 inches). Executive: 184 x 267 mm (7.2 x 10.5 inches), B5 (JIS): 182 x 257 mm (7.2 x 10.1), B5 (ISO): 176 x 250 mm (8.5 x 13 inches): 216 x 330 mm (8.5 x 13 inches), tray 3 (HP LaserJet 2200DTN) and optional 500-sheet input tray: A4: 210 x 297 mm (8.3 x 11.7 inches), Letter: 216 x 279 mm (8.5 x 11 inches). Automatic duplex unit: supports A4, Letter, Legal, 216 x 279 mm (8.5 x 13 inches). Printable area: left/right margin: 4.0 mm (.16 inch), top/bottom margin: 4.0 mm (.16 inch).
|
| Control panel: |
Simplified front panel with GO and JOB-CANCEL buttons and LEDs for status
|
| Standard software: |
Drivers In-box: Microsoft Windows NT 4.0, 3.1x (PCL 5e only), 9x, 2000, Me, Macintosh System 7.5.5 and above.
Drivers on the Web: Windows 3.1x (PCL 5e only), Windows 95/98/2000/NT4.0/Me/XP, IBM OS/2, and Mac OS 8/9/X. For the latest driver updates, go to
www.hp.com/cposupport/software
.
For information on Open Source and Linux from HP, or on model scripts for UNIX(R)/LINUX,
click here
(http://www.hp.com/products1/linux/printers_and_linux.html).
Printing from DOS-based applications is possible in compatibility mode. Software disk replication utility for attended or unattended deployment of custom drivers. HP internet installer can automatically update printer drivers during installation. HP Web Jetadmin printer management software for network configuration and management from a common web browser.
|
| System requirements: |
Operating system requirements as recommended by the operating system vendor plus 15 MB free hard disk space, CD-ROM disk drive, USB port or (Windows only) dedicated IEEE-1284 compliant bi-directional parallel port.
|
| Economical printing: |
Economode capable (saves up to 50% toner at 600 dpi), duplexing, N-up printing
|
| Operating and environmental ranges: |
Temperature for printer and toner cartridge: Operating: 15° to 32.5° C. Storage/Standby: -20° to 40° C . Humidity: Operating: 10% to 80% RH (no condensation). Storage: 10% to 90% RH. Acoustics (per ISO 9296): LpAm 58 dB (A) Operator position, LpAm 52 dB (A) Bystander position (1m). Sound power: LWAd 0 Bels (A) Powersave, LWAd 6.6 Bels (A) Printing
|
| Power requirements: |
Source: 220 to 240 V (+/-10%), 50/60 Hz (+/-3Hz) or 100 to 127 V (+/- 10%), 50/60 Hz (+/-3Hz). Power consumption (average): HP LaserJet 2200 series printers (220 V): Off = 0 W, Standby / Powersave: 14 W, Printing: 360 W. HP LaserJet 2200 series printers (110 V): Off = 0 W, Standby / Powersave: 12 W, Printing: 360 W. Circuit capacity: Minimum 2.5 A (220 V) and 5 A (110 V)
|
| Size/weights: |
W x D x H: HP LaserJet 2200D/DN/DSE: 405 x 435 x 255 mm (16 x 17.1 x 10 inches), HP LaserJet 2200DT: 405 x 435 x 334 mm (16 x 17.1 x 13.1 inches), HP LaserJet 2200DTN: 405 x 435 x 395 mm (16 x 17.1 x 15.6 inches), 250-sheet input tray: 405 x 435 x 79 mm (16 x 17.1 x 3.1 inches), 500-sheet input tray: 405 x 435 x 140 mm (16 x 17.1 x 5.5 inches). Weight: HP LaserJet 2200D/DN: 14.0 kilograms (30.9 pounds), HP LaserJet 2200DT: 17.1 kilograms (37.7 pounds), HP LaserJet 2200DTN: 18.7 kilograms (41.2 pounds), 250-sheet input tray: 3.1 kilograms (6.8 pounds), 500-sheet input tray: 4.7 kilograms (10.4 pounds)
|
| Certifications: |
Carries CE marking for EU EMC and low voltage directives; complies with IEC 60950/EN 60950 and IEC 60825- 1/EN 60825-1 (Class 1 Laser product/LED product); FCC Class B and CISPR-22 Class B; CDRH certified Class 1 Laser Product (safe for office/EDP use); TÜV-GS approved; EPA ENERGY STAR compliant; Blue Angel eco-label certified
|
| Supplies life: |
HP LaserJet Ultraprecise print cartridge capacity rated at average 5,000 pages with 5% coverage.
|
| Duty cycle: |
Up to 40,000 pages per month
|
| Warranty: |
One year return to HP/dealer upgrade basic warranty with options that include 3 years on-site response or repair/replacement
|
FCC regulations
The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. The limits are designed to provide reasonable protection against harmful interference in a residential installation. The equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation; the presence of interference can be determined by turning the equipment off and on. If the equipment does cause harmful interference to radio or television communications, try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase distance between equipment and receiver
Connect equipment to an outlet on a circuit different from that to which the receiver is located
Consult the dealer or an experienced radio/television technician
|
NOTE:
|
Any changes or modifications to the printer that are not expressly approved by HP could void the authority to operate the equipment. Use of a shielded interface cable is required to comply with the Class B limits of Part 15 of FCC rules. |
Environmental Product Stewardship program
Hewlett-Packard Company is committed to providing quality products in an environmentally sound manner. This product has been designed with several attributes to minimize impacts on our environment.
Ozone production
This product generates no appreciable ozone gas (O 3 ).
Energy consumption
Energy Star
This product is designed to reduce power consumption and save natural resources without compromising product performance. It has been designed to reduce total energy consumption both during operation and when the device is not active.
This product qualifies for ENERGY STAR®
, a voluntary program established by the U.S. Environmental Protection Agency (EPA) to encourage the development of energy-efficient office products.
Figure 1: ENERGY STAR® logo
ENERGY STAR®
is a U.S. registered service mark of the U.S. EPA. As an ENERGY STAR®
partner, HP has determined that this product meets ENERGY STAR®
guidelines for energy efficiency.
For more information about ENERGY STAR ®
, go to the EPA's
ENERGY STAR® Web site
(www.energystar.gov) (in English). Paper usage
This product’s duplex feature (two-sided printing) and N-up printing capability (multiple pages printed on one sheet of paper) can reduce paper usage and the resulting demands on natural resources.
|
NOTE:
|
The simplex version of the HP LaserJet 2200 printer family (base model number C7064A) supports manual duplexing only. |
Plastics
Plastic parts over 25 grams are marked according to international standards that enhance the ability to identify plastics for recycling purposes at the end of the product’s life.
Printing supplies
In many countries, the product's printing supplies (for example, toner cartridge, drum, fuser) can be returned to HP through the HP Planet Partners Printing Supplies Environmental Program. An easy-to-use and free take back program is available in over 25 countries. Multi-lingual program information and instructions are included in every new HP LaserJet Toner Cartridge and Consumables package.
Printing Supplies Environmental program
Since 1990, the HP LaserJet Toner Cartridge Recycling Program has collected more than 39 million used LaserJet toner cartridges that otherwise may have been discarded in the world's landfills. The HP LaserJet toner cartridges and consumables are collected and bulk shipped to our resource and recovery partners who disassemble the cartridge. After a thorough quality inspection, selected parts are reclaimed for use in new cartridges. Remaining materials are separated and converted into raw materials for use by other industries to make a variety of useful products.
U.S. returns
For a more environmentally responsible return of used cartridges and consumables, HP encourages the use of bulk returns. Simply bundle two or more cartridges together and use the single, pre-paid, pre-addressed UPS label that is supplied in the package.
Non-U.S. returns
Non-US customers should call the local HP sales and service office.
Material Safety Data Sheet
Toner consumption
EconoMode uses significantly less toner, which might extend the life of the toner cartridge with minimal impact to print quality.
Declaration of Conformity
| Declaration of Conformity
|
|
|---|
| according to ISO/IEC Guide 22 and EN 45014:
|
| Manufacturer's Name: |
Hewlett-Packard Company
|
| Manufacturer's Address: |
11311 Chinden Boulevard
Boise, Idaho 83714-1021, USA |
| declares, that the product:
|
| Product name: |
HP LaserJet 2200d, 2200dt, 2200dn, 2200dtn, 2200dse |
| Model numbers: |
C7058A, C7059A, C7063A, C7061A, C7062A, C4793A*, C7065A**
|
NOTE:
|
* C4793A is the optional 250-sheet input tray. **C7065A is the optional 500-sheet input tray. |
|
| Product options: |
All |
|
conforms to the following Product Specifications:
|
| Safety: |
IEC 60950:1991+A1+A2+A3+A4 / EN 60950:1992+A1+A2+A3+A4+A11
IEC 60825-1:1993+A1 / EN 60825-1:1994+A11 (Class 1 Laser/LED Product)
|
| EMC: |
CISPR 22:1997 / EN 55022:1998 Class B 1
EN 61000-3-2:1995
EN 61000-3-3:1995
EN 55024:1998
FCC Title 47 CFR, Part 15 Class B 2 / ICES-002, Issue 2
AS / NZS 3548:1995
|
|
Supplementary Information:
|
| The product herewith complies with the requirements of the EMC Directive 89/336/EEC and the Low Voltage Directive 73/23/EEC, and carries the CE-marking accordingly. |
| |
The product was tested in a typical configuration with Hewlett-Packard Personal Computer Systems.
This Device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Product exhibits Class A operation when connected to Local Area Network (LAN) cables using print server accessories.
|
Country/Region-specific safety statements
Laser safety statement (USA)
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration has implemented regulations for laser products manufactured since August 1, 1976. Compliance is mandatory for products marketed in the United States. The printer is certified as a “Class 1�? laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968. Since radiation emitted inside the printer is completely confined within protective housings and external covers, the laser beam cannot escape during any phase of normal user operation.
| WARNING:
|
Using controls, making adjustments, or performing procedures other than those specified in this user guide may result in exposure to hazardous radiation.
|
DOC requirements (Canada)
Complies with Canadian EMC Class B requirements.
«Conforme à la classe B des normes canadiennes de compatibilité électromagnétiques «CEM».»
LED safety statement
The infrared port on the front panel of this printer is classified as a Class 1 LED (Light Emitting Diode) device according to International Standard IEC 60825-1 (EN 60825-1). This device is not considered harmful, but the following precautions are recommended.
If the printer requires service, contact an authorized HP service center.
Do not attempt to make any adjustments of the printer.
Avoid direct eye exposure to the infrared LED beam.
Be aware that the beam is invisible light and cannot be seen.
Do not attempt to view the infrared LED beam with any type of optical device.
|
|
Printable version
