spacer
hp.com home

HP Support document

»Return to original page

HP LaserJet Legacy Printers - Memory Upgrade Specifications


This document provides part number and specification information for memory upgrades on various legacy HP LaserJet printers.
NOTE: The following part numbers may change or become discontinued without further notice.
HP LaserJet 5L / 6Lseries Printers
See Table 1 for memory SIMM part numbers or the HP LaserJet 5L or 6L series printers.
Table 1: Memory part numbers
1-MB SIMM C3939A
2-MB SIMM C3938A
4-MB SIMM C3148A
The specifications for the above memory SIMMs are:
  • DRAM
  • 5 Volt
  • 70 nanoseconds (or slower, such as 70ns or 100ns)
  • Meets JEIDA Specifications
NOTE: An 8 MB SIMM from Kingston Technologies can be used in these printers.
HP LaserJet 4P, 4 Plus, 4V, 5P, 5, 5Si, and 6P series printers
See Table 2 for memory SIMM part numbers for the HP LaserJet 4P, 4 Plus, 4V, 5P, 5, 5SI and 6P series printers.
Table 2: Memory part numbers
1-MB SIMM* C3130A (Discontinued)
2-MB SIMM C3131A (Discontinued)
4-MB SIMM C3132A (Discontinued)
8-MB SIMM C3133A (Discontinued)
16-MB SIMM* C3146A
The specifications for the above memory SIMMs are:
  • 72 Pin
  • 32 Bit (No Parity)
  • 70 nanoseconds (or slower, such as 80 ns or 90 ns)
  • Presence Detect
    NOTE: The 16-MB SIMM is not supported on the HP LaserJet 4P/4MP, and 4/4M printers. The 1-MB SIMM is not supported on the HP LaserJet 5Si/5Si MX and 5Si Mopier printers.
HP LaserJet IIISi, 4 and 4Si series printers
See Table 3 for memory SIMM part numbers for the HP LaserJet IIISi, 4 and 4Si series printers.
Table 3: Memory part numbers
8-MB SIMM C2066A
The specifications for the above SIMM are as follows:
  • 72 pin
  • 36 bit (Parity)
  • 80 nanoseconds
  • Presence Detect
    NOTE: This memory is also compatible with the HP LaserJet 4P/4MP, 4 Plus/4M Plus and 4V/4MV printers. However, it is recommended to use the SIMM part numbers specific to those printers. Presence detect must be present on all the above listed SIMMs. HP LaserJet IIISi printers with serial numbers prior to 3200 cannot use the 8 MB SIMM (C2066A).
Presence detect requirements
Presence detect is the ability to report the size and speed of the SIMMs installed in an HP LaserJet printer to whomever is asking for the information. Without presence detect, the printer would be unable to recognize that additional memory had been installed.
HP LaserJet 4L printer
The HP LaserJet 4L printer has a 1-MB memory upgrade. The part number is: C2024-69001.

   Content feedback
To help us improve our content, please provide your feedback below.

1. How does the information on this page help you?

   very helpful somewhat helpful not helpful
 

2. Was it easy to find this document?

   easy not easy

3. If you selected not easy for question 2, in which section did you expect to find it?

     

4. Comments:

 
 
- Your feedback will be used to improve our content. Please note this form is for feedback only, so you will not receive a response.
Contact HP if you need technical assistance.
» Return to original page
 
Privacy statement Using this site means you accept its terms Feedback to webmaster
© 2010 Hewlett-Packard Development Company, L.P.